عجلة مشط التبن Walvoil DPX100 ثمانية أقسام مع عصا تحكم صغيرة من نوع Can Bus Otto لـ آلات قطع الأشجار

Walvoil DPX 100 12/24 V hydraulic valve with 8 proportional sections, open/closed centre and additional levers. The valve includes a post-compensation section.

Otto Canbus 12/24 V joysticks.

This kit is configured for the most common machine set-ups and supports up to 8 standard forestry crane functions. If you require a different dedicated configuration, we can tailor it to your needs, including variations in coils, voltage, number of sections, anti-shock valves, connections, etc.

The kit is designed for plug-and-play convenience. We take care of everything from the connectors to the software configuration.

We offer technical support and are available at any time via email, WhatsApp and telephone.

If you have any questions or require assistance, you can contact us at any time at - or -.

Once the order has been placed, flow rate and pressure can be fully customised to the customer’s specific requirements.


-------------------------------------------------- ------------------------------------------------- - -------------------------------------------------- --------

Walvoil DPX 100 hydraulic section valve with compensation, fully proportional

Technical specifications of the standard configuration:

Inlet section: 32 GPM 120 l/min – Pmax 300 bar 4351 psi Power supply connection: 3/4‘ BPS, tank return connection: 3/4’ BPS

1. Main boom 60 l/min 16 GPM anti-shock valves 190/80 bar 2755/1305 psi A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever

2. Boom 60 l/min 16 GPM anti-shock valves 190/220 bar 2755/3190 psi A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors and hand lever

3. Swing 40 l/min 10 GPM anti-shock valves 200/200 bar 2900/2900 psi A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors and hand lever

4. Extension 80 l/min 21 GPM anti-shock valve 140 bar/closed rod 2030 psi side A 4/3 centre; A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors and hand lever

5. Rotator 20 l/min 5 GPM, A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors and hand lever

6. Grapple 60 l/min 16 GPM, A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors and hand lever

7. Left leg support 20 l/min 5GPM A+B closed circuit, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors and hand lever; Spool: 20 l/min; No anti-shock valves

8. Right leg support 20 l/min 5 GPM A+B closed, electro-hydraulic control on both sides with AMP-JPT or Deutsch connectors with hand lever; Spool: 60 l/min; No anti-shock valves

Outlet section: with the option to combine valves, with a vent valve (LS relief), with a pressure-reducing valve. Control port “V” and drain port “L” closed. Side connections “T1”, “P1”, “LS1” sealed. DBV fixed and sealed to 175 bar at 90 l/min.

-------------------------------------------------- ------

CANBus Otto Joysticks

CANBus board for analogue/digital inputs.

DESCRIPTION

MDCi is an electronic circuit board with a CANBus interface

Simulate 2 JC joysticks using 2 Otto joysticks and a push-button dashboard.

Transmission takes place immediately upon switching on the

electronic board.

FEATURES

- Supply voltage from 10 to 30 Vdc

- CAN V2.0B communication bus

- 120-ohm internal terminating resistor not present in this version

- 2 diagnostic LEDs (red and green)

- Firmware can be updated via the integrated serial interface

SIGNALS

Red LED flashes once: Short-circuit fault on the stabilised +5V output

Red LED flashes twice: One of the analogue inputs was detected as not being in the rest position upon power-up

The input is disabled until a reset is performed.

Green LED is lit: The circuit board is functioning correctly.

The green LED flashes once each time the status of an input (analogue or on/off) changes.

MDCi control unit for OTTO joystick interface
and button panel for Waldkranich
Installation version: X1
Firmware: mdc_P5_01.hex
Config file: mdc_P5_01.cfg

--------------------------------------------------
------

Technical specifications:

Supply voltage: 10 VDC to 30 VDC (internal 5x20 8A fuse, type F8A)

Current consumption: 300 mA + load outputs (max. 7.5 A)

Operating temperature range: -20 ÷ +70 °C

Power supply for external potentiometers: +5 V – max. current 50 mA

Minimum PWM current range: from 100 to 2500 mA

Maximum PWM current range: from 100 to 2500 mA

PWM frequency: 50–60–70–85–100–125–150–200–250–300 Hz

Impedance of analogue inputs: 11 kOhm at 2.5 V

Overall dimensions with connector fitted: 256 × 210 × 45 mm

Drill hole dimensions: 242 x 142 mm (4 holes, 6 mm in diameter)

-------------------------------------------------- ------

NOTE:
To achieve a cable length of L = 1.5 m, you must
- Make the joystick/cable connections using 7x0.75 mm² wire by removing the
original connectors
- Insert the corrugated sheath and secure it to the underside of the joystick (see photo).
- Connect the 7x0.75 cable to the 6-pin Deutsch socket
(these are small contacts)